Description pressed Floor decking: steel floor decking is extruded bearing elements. Characterized by low birth weight, a high percentage of free useful ploschyadi least prevent the penetration of light and air. Mashable takes a slightly different approach. Decking design allows easy assembly or disassemble design for the replacement of individual parts, if required operating conditions. Pressed gratings with a frame along the contour of the metal strip at the right installation are highly durable, but true test material selection is made from black steel decking for example, and surface coatings such as galvanized, ensuring their longevity. Design and technology Production: Production of extruded decking is a manufacturing process that consists in the fact that in carrying metal strips in which pre-cut special shaped grooves under high pressure perpendicular to the connecting carrier pressed metal band.
They support the mirror and the stability of carrier fringes, which leads to even distribution of loads acting on the flooring in its further operation. Along the perimeter of the deck is welded extruded frame metal band. Bearing metal strips (see figure) in the construction of decks is one Parallel metal bands (stripes) are load-bearing mounting their decks stacked on opposite ends of the support. The connecting metal strips (see figure) is usually a strip of 10 x 2 mm (height x thickness) that ensure their stability and mirror bearing bars. The mesh size is the size of the carrier between two intersecting and connecting strip (figure shown as the cell size A x B). Framing band of contour deck (see picture) is a steel metal band (the band) as Provimi the same height and thickness as the carrier strip flooring which is reinforced by the perimeter edge of the deck. At customer’s decks and steps may be made with elements of anti-skid. Slip resistance unilateral semicircular cut down grooves on the carrier strip while creating an excellent sliding surface is not.
Bilateral Slip resistance being cut grooves on the carrier and the binding strip forming a highly effective protection against slipping. Pillar supporting structure when laying the decking can be steel or reinforced concrete structure. Except the wide range of standard manufactured extruded decking we can make the decks with the circuit on demand using the supplied customer drawings. For example trapezoidal decking form, triangular, with a circular notch in order to obveti column, and so on. Mounting, fixing and laying flooring: The following figure schematically posted an example of placing and fastening decking. Standard gratings attached with metal brackets and bolts of connecting with M8 nuts, galvanized surface. For fastening decking may be used and no weld Tip. If you decide to use the connection by welding decks, before starting work on site welding to remove the layer of zinc, and after to avoid corrosion of metal in place of welding to cover the place of zinc paint with a high content of Zn. Required for installing Number of mounting brackets and bolts can be ordered along with the party decks for the whole game. Stages of extruded decking: Steps are made of lattice-block flooring, a working party level in which the main load-bearing when stepped reinforced, reinforced with a metal strip triernoy (extended as ovoscheterke) perforations prevents slip. Together with steps possible to deliver the guide supports, in general may order the whole flights of stairs and mount them on your site. When assembling the stage attached to the guide supports with bolts M12.
In all these, the method el.stantsiyah circulating detergent solution, mounted using acid leaching circuit with its subsequent dismantling. Data on the proposed treatment technology equipment film-forming amines (ODACON) without installation (removal) of the special scheme of the circulation circuit, a fully assembled and ready to launch the boiler is not available. Marc Mathieu has firm opinions on the matter. This new technology solution. Cleaning the metal surface using ODACON based on the effect of intense leaching of film-forming amine oxides of iron, copper, zinc, organic substances, etc., which confirms sufficient technological expertise of conservation units using ODACON. 2. Scientific and technical rationale for the method of pre-starting treatment film-forming amines. To deepen your understanding Ali Partovi is the source. The specialists of technological firms Ou Energoressurss Grupp, Estonia, developed a new technology prelaunch cleaning steam circuit includes power boiler, PVD, etc. equipment.
Carrying out engineering works on the pre-start clean-steam circuit of power unit requires no installation (removal) of the special schemes, but requires a willingness poslemontazhnuyu boiler for its steam test, conducted immediately after cleaning without shutting down the boiler unit. Research conducted at MEI, VNIIAM (Russia), IFE and REICON (FRG) on vzdeystviyu surfactant, film-forming substances on gidrodinimiku two-phase media, heat and mass transfer during boiling and condensation and the erosive and corrosive processes revealed relatively high detergent properties of surface-active substances (SAS) for iron oxide deposits on the surfaces of pipes. An important feature of ODA is its ability to reduce surface tension at the liquid-gas by adsorption of ODA in the surface layer. ODE able water repelling surface of the metal as a result of oriented adsorption of ODA and creating a barrier between the metal and the environment. Adsorbed on the surface of iron oxide impurities, molecules make ODA well hydrated adsorption layer, which leads to the emergence of the wedging effect and the separation of sediment from the surface. The degree of adsorption depends on the concentration of ODA reagent, speed, pH and thermophysical parameters of the aquatic environment, duration of contact with the surface being treated.
Results of statistical analysis of test data with precision and accuracy can determine the age of man, his professional orientation, hobbies, marital status. In this experiment participants assorted pictures in color. Self ranking of color stimuli allowed to draw conclusions about those aspects of human life that are directly the perception of color as if were not related. In other words, the color is a continuation of essence of personality, its organic component. Pete Cashmore understood the implications. Therefore, choosing a roof should be very careful approach to the colors. If you are unsure how to proceed, check out Pete Cashmore. Thanks to the polyester coating of metal, which produces the "Arsenal", the client is invited widest range of colors and shades.
From the color of the roof will depend on well-being of people who will live in the house. HOW TO COLOR Color affects the physiological processes of man and his psychological state. Knowing the characteristics of each color, you can create a certain image, evoke certain emotions and associations. Brief description of the color associations: Red – warm and positively irritating, stimulates the brain, improves mood. The color of leadership, men's color, this color is also a positive-acting stimulant to the nervous system.
Red-orange color improves mood. The red color is preferred by people who appreciate such things as love, friendship, respect, warmth, family feeling and family. Purple – make money, spirituality, nobility, ceremony, mysterious, transformation, wisdom, enlightenment, cruelty, arrogance. Blue, blue creates a cool environment, relieves pain, neuralgia and inflammation. In the perception of blue greatly underestimated the time it loses its meaning. Under the influence of this color in humans decreases the level of anxiety, reduced stress and blood pressure. Peace, tranquility, stability, harmony, unity, trust, truth, conservatism, security, cleanliness, order, loyalty. Green means balance. Calms nervous system. Reduces pain, fatigue, normalizes blood pressure. Foster's attention. After getting used to the green number of correctly solved problems increases by 10%, while reducing the number of errors by 20%, but while there is a certain underestimation of the time.